|

Investigating the Structure and Properties of the AlSi10Mg Alloy Manufactured by Means of Selective Laser Melting

Authors: Karavaev A.K., Puchkov Yu.A. Published: 19.10.2020
Published in issue: #5(134)/2020  

DOI: 10.18698/0236-3941-2020-5-71-85

 
Category: Mechanical Engineering and Machine Science | Chapter: Manufacturing Engineering  
Keywords: additive manufacturing, selective laser melting, aluminium alloys, AlSi10Mg

The paper investigates the structure and properties of samples made of ASP-25 AlSi10Mg, a Russian powder designed to replace expensive additive manufacturing powders of European origin featuring the same chemical composition. We detected that the particle size in the ASP-25 AlSi10Mg powder varies in the range of 7 to 50 μm, the average particle size being 23 μm for the standard deviation of 9.15 and dispersion of 83.7. On the surface of powder particles, we observed smaller satellite particles, individual aggregates, and particles of pure aluminium. We detected the following at the transition boundary between adjacent tracks: a columnar crystal zone and a heat-affected zone consisting of three layers of large, medium and small grains generated as a result of varied cooling conditions. These grains display different silicon lattice thicknesses along their boundaries. We detected no critical size pores (over 15 μm) or burning in the heat-affected zone. The fact that microhardness increases towards the sample edges and is non-monotonic over the transverse section is due to a range of factors acting simultaneously to create non-uniform temperature and force fields that cause differences in conditions of structure formation. Fractography studies of fractures in the AlSi10Mg alloy showed that the nature of failure varies along the sample depth. The central part of the sample, which is subjected to the highest thermal effects, shows clear signs of viscous failure along the main cracks developing along the boundaries of construction layers. We showed that the AlSi10Mg alloy is more resistant to pitting corrosion and general corrosion than the AK9сh (AK9ч) alloy

References

[1] Aboulkhair N.T., Everitt N.M., Ashcroft I., et al. Reducing porosity in AlSi10Mg parts processed by selective laser melting. Addit. Manuf., 2014, vol. 1-4, pp. 77--86. DOI: https://doi.org/10.1016/j.addma.2014.08.001

[2] Cabrini M., Calignano F., Fino P., et al. Corrosion behavior of heat-treated AlSi10Mg manufactured by laser powder bed fusion. Materials, 2018, vol. 11, no. 7, art. 1051. DOI: https://doi.org/10.3390/ma11071051

[3] Leon A., Shirizly A., Aghion E. Corrosion behavior of AlSi10Mg alloy produced by additive manufacturing (AM) vs. its counterpart gravity cast alloy. Metals, 2016, vol. 6, no. 7, art. 148. DOI: https://doi.org/10.3390/met6070148

[4] Mauduit A., Pillot S., Frascati F. Application study of AlSi10Mg alloy by selective laser melting: physical and mechanical properties, microstructure, heat treatments and manufacturing of aluminium metallic matrix composite (MMC). Metall. Res. Technol., 2015, vol. 112, no. 6, art. 605. DOI: https://doi.org/10.1051/metal/2015039

[5] Ming Tang. Inclusions, porosity, and fatigue of AlSi10Mg parts produced by selective laser melting. Ph. D. Thesis. 18 April 2017, CMU. Pittsburgh, PA, USA, 2017.

[6] Thijs L., Kempen K., Kruth J.P., et al. Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder. Acta Mater., 2013, vol. 61, no. 5, pp. 1809--1819. DOI: https://doi.org/10.1016/j.actamat.2012.11.052

[7] Thijs L., Kempen K., Kruth J.-P., et al. Mechanical properties of AlSi10Mg produced by selective laser melting. Phys. Procedia, 2012, vol. 39, pp. 439--446. DOI: https://doi.org/10.1016/j.phpro.2012.10.059

[8] Trevisan F., Calignano F., Lorusso M., et al. On the selective laser melting (SLM) of the AlSi10Mg alloy: process, microstructure and mechanical properties. Materials, 2017, vol. 10, no. 1, art. 76. DOI: https://doi.org/10.3390/ma10010076

[9] Verkens D. Study of the anodizing behavior of additive manufactured AlSi10Mg aluminium alloy. Master thesis. Brussel, ULB, 2017.

[10] EOS aluminium AlSi10Mg. eos.info: website. Available at: https://www.eos.info/en/additive-manufacturing/3d-printing-metal/dmls-metal-materials/aluminium-al (accessed: 15.02.2020).

[11] Zlenko M.A., Nagaytsev M.V., Dovbysh V.M. Additivnye tekhnologii v mashino-stroenii [Additive technologies in machine building]. Moscow, NAMI Publ., 2015.

[12] Zlenko M.A., Popovich A.A., Mutylina I.N. Additivnye tekhnologii v mashinostroenii [Additive technologies in machine building]. St. Petersburg, SPbGU Publ., 2013.

[13] Ryabov D.K., Zaytsev D.V., Dynin N.V., et al. Alternation of mechanical features of alloy AK9ch manufactured by selective laser melting. Trudy VIAM [Proceedings of VIAM], 2016, no. 9, pp. 20--29 (in Russ.). DOI: https://doi.org/10.18577/2307-6046-2016-0-9-3-3

[14] Smurov I.Yu., Movchan I.A., Yadroytsev I.A., et al. Experimental additive straight manufacturing by lazer. Vestnik MGTU Stankin [Vestnik MSTU STANKIN], 2012, no. 2, pp. 48--50 (in Russ.).

[15] Puchkov Yu.A., Babich S.G., Fomenko G.S., et al. Computerized methods system for electrochemical corrosion investigation. MiTOM, 1996, no. 5, pp. 37--39 (in Russ.).