Simulation of processes in the “inlet collector–cylinder” system of aviation reciprocating engine with distributed fuel injection
Authors: Kavtaradze R.Z., Zelentsov A.A., Onishchenko D.O., Finkelberg L.A., Kostyuchenkov A.N. | Published: 10.06.2013 |
Published in issue: #4(89)/2012 | |
DOI: | |
Category: Power-generating and Transport Machine Building | |
Keywords: aviation reciprocating engine, inlet system, turbulent combustion, mathematical model, numerical methods |
Semitransparent thermal barrier coating with reflective oxidized sublayer
Authors: Merzlikin V.G., Bekaev A.A., Sutugin V.G., Kuznetsov Yu.A. | Published: 10.06.2013 |
Published in issue: #4(89)/2012 | |
DOI: | |
Category: Power-generating and Transport Machine Building | |
Keywords: thermal barrier material, semi-transparent heat-insulating coating, scattering, absorption, volume heating, high-speed diesel |
Study of fuel jet evolution in diesel combustion chambers
Authors: Rudakov V.Yu., Karelin A.N. | Published: 10.06.2013 |
Published in issue: #4(89)/2012 | |
DOI: | |
Category: Power-generating and Transport Machine Building | |
Keywords: Meshchersky equation, zone and turbulent fuel jets, engine with transparent windows, regime of combustion bomb, regime of diesel fuel combustion, high-speed shooting, injection duration |
Influence of spacer type on fluid dynamics of 7-rod fuel assembly
Authors: Markov P.V., Solonin V.I. | Published: 11.06.2013 |
Published in issue: #1(90)/2013 | |
DOI: | |
Category: Power-generating and Transport Machine Building | |
Keywords: fast fission reactors, spacing of fuel rods, fuel rods, computational fluid dynamics, subchannel transfer |
Effect of laws of power flow distribution over propulsion units of a wheeled vehicle on its operation properties
Authors: Larin V.V. | Published: 11.06.2013 |
Published in issue: #1(90)/2013 | |
DOI: | |
Category: Power-generating and Transport Machine Building | |
Keywords: wheeled vehicle, power, control, electrical machine, traction drive, transmission, road surface, wheel, resistance to movement, thrust |
Improvement of construction of motor car body at the designing stage to satisfy passive safety requirements at offset frontal impact
Authors: Zuzov V.N., Zuzov I.V. | Published: 11.06.2013 |
Published in issue: #1(90)/2013 | |
DOI: | |
Category: Power-generating and Transport Machine Building | |
Keywords: motor car, car body, passive safety, frontal impact, energy-absorbing capacity, rigidity |
Statement of Boundary Conditions in Mathematical Description of Diesel Fuel Flow in a Tube
Authors: Grishin Yu.A., Khmelev R.N., Bazaeva N.S. | Published: 29.08.2013 |
Published in issue: #2(83)/2011 | |
DOI: | |
Category: Power-generating and Transport Machine Building | |
Keywords: diesel fuel, mathematical simulation, boundary conditions, Godunov’s method |
Results of Semi Full-Scale Simulation of Dynamical Modes of Diesel-Locomotive Power Unit
Authors: Kuznetsov A.G. | Published: 29.08.2013 |
Published in issue: #3(84)/2011 | |
DOI: | |
Category: Power-generating and Transport Machine Building | |
Keywords: simulation, power unit, diesel-locomotive, dynamical modes |
Substantiation of Control and Protection System of Trickling Radiative Cooler for Realization of Prescribed Sequence Diagram of Unit Operation
Authors: Nechaev M.V., Nechaev V.Yu. | Published: 29.08.2013 |
Published in issue: #3(84)/2011 | |
DOI: | |
Category: Power-generating and Transport Machine Building | |
Keywords: space experiment, low-potential heat, heat removal, radiative cooler, onboard control system |
Computational and Experimental Study of Influence of Piston’s and Sleeve’s Thermal Insulation on Formation of Nitrogen Oxides in Combustion Products of High-Speed Diesel
Authors: Kavtaradze R.Z., Onishchenko D.O., Zelentsov A.A., Kadyrov S.M. | Published: 29.08.2013 |
Published in issue: #4(85)/2011 | |
DOI: | |
Category: Power-generating and Transport Machine Building | |
Keywords: diesel, combustion chamber, thermal insulation, piston, sleeve, nitrogen oxides |